Harrison Steel Castings Co.
  • Machining
  • Attica, IN, USA
  • $15.45+
  • Hourly
  • Full Time

Benefits available after 90 days include 401k with profit sharing, Medical, Dental, Vision, Life Insurance, Short and Long Term Disability, and company-sponsored health clinic.

Summary: Sets up and operates conventional and special purpose machines to machine castings to customer specifications. Once trained, this position will work our 2nd shift, which is normally 3pm-11pm.

 Essential Duties and Responsibilities include the following. Other duties may be assigned.

  • Starts up, operates and shuts down the assigned machine tool.
  • Ensures that castings are machined to print specifications.
  • Completes all required production paperwork.
  • Uses gauges commonly associated with machining type work.
  • Reads and writes programs for machining processes.
  • Performs daily TPM maintenance.
  • Inspects all lifting devices for condition and wear.
  • Wears required safety equipment.
  • Follows job work instructions and training matrix, where applicable.


To perform the job successfully, an individual should demonstrate the following competencies: analyzes complex or diverse information; demonstrates attention to detail; reads and interprets written information; demonstrates accuracy and thoroughness; follows policies and procedures; has ability to deal with frequent change, delays, or unexpected events; is consistently at work and on time; follows instructions, responds to management direction; uses time efficiently; meets productivity standards; completes work in timely manner; works quickly; observes safety and security procedures; uses equipment and materials properly.                                           


To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.


  • High school diploma or general education degree (GED); or one to three months related experience and/or training; or equivalent combination of education and experience.
  • Manufacturing/classroom training at tool manufacturers or technical school.
  • On-the-job training until competence is shown in machining castings.
  • Blue print reading.

Language Ability:

Ability to read and interpret documents such as safety rules, operating and maintenance instructions, and procedure manuals. Ability to write routine reports and correspondence. Ability to speak effectively.

Math Ability:

Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals. Ability to compute rate, ratio, and percent and to draw and interpret bar graphs.

Reasoning Ability:

Ability to apply common sense understanding to carry out detailed but uninvolved written or oral instructions. Ability to deal with problems involving a few concrete variables in standardized situations.

Computer Skills:

To perform this job successfully, an individual should have a working knowledge of computers.

Certificates and Licenses:

Fork truck license

Certificates for any outside manufacturing/classroom training

Supervisory Responsibilities:

This job has no supervisory responsibilities.

Work Environment:

The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

While performing the duties of this job, the employee is regularly exposed to work near moving mechanical parts. The employee is frequently exposed to wet or humid conditions (non-weather) and fumes or airborne particles. The employee is occasionally exposed to work in high, precarious places; outdoor weather conditions; extreme heat (non-weather); risk of electrical shock and vibration.

The noise level in the work environment is usually loud.

Physical Demands:

The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

The employee must regularly lift and /or move up to 25 pounds, frequently lift and/or move up to 70 pounds. Specific vision abilities required by this job include Close vision, Distance vision, Peripheral vision, Depth perception and Ability to adjust focus. While performing the duties of this Job, the employee is regularly required to walk; use hands to finger, handle, or feel; reach with hands and arms and talk or hear. The employee is frequently required to stand. The employee is occasionally required to sit; climb or balance; stoop, kneel, crouch, or crawl and taste or smell.

Harrison Steel Castings Co.
  • Apply Now

    with our quick 3 minute Application!

  • * Fields Are Required

    What is your full name?

    How can we contact you?

    I agree to ApplicantPro's Applicant Information Use Policy.*
  • Sign Up For Job Alerts!

  • Share this Page
  • Facebook Twitter LinkedIn Email
Logo Contact us today! / Highly Engineered... About Us Capabilities Value Added Quality Philosophy Gallery